中文版   English  
 
News Center
 · Strengthen the three dialectic
 · Let mobile compressor run fast
 · Polyurethane insulation cotton
 · Air to water heater industry -
 · Vacuum drying box using the pr
 · Heat pump quality guarantee "c
 · Air compressor motor protectio
 · Water pump
Contact Us
  • Address:Qinghu cun, Qishi Town, Dongguan, Guangdong Province
    Contact Person:Mr Yan
    E-Mail:zhihe998@126.com
    Tel:+86-0769-86723636
    Fax:+86-0769-81080026
    Mobile:13829228807  
               13829282260
    QQ:2463307187    
    WebSite: www.dg-zhihe.cn

 
News Center Location: Home > News
 

To the oil tank insulation
Author: 志和      Release Date:2014/4/8      View Count:1677
 

The air compressor is an open cycle, air is constantly put water and dust into the air compressor system. The dust pollution of the lubricating oil, pollution of the oil core,pollution of the oil filter, servo cylinder in the air inlet valve will deposition on cooler,deposited in the temperature control valve, electromagnetic valve, deposited on theinside, are wrong incentives.

Water vapour in the air condenses on the pressure machine internal into liquid waterunder certain conditions. Water will cause the metal parts rust rust, the most serious is the oil tank and the inner wall of the cover plate.

Screw machine downtime hours later, mixed in the lubricating oil in the water will beseparated, deposited in the low-lying machines, such as the bottom of the cylinder,the bearing chamber, pipe joints of walls, a few hours then let these surface with a layer of rust.

If the screw machine to put a few days holiday, probably long after the first launch isstuck rotor. The first launch of always first artificial barring experienced users andmaster long after the.

The compressor run oil is often the oil return hole blocking the formation, which iscorroded to blame. The intake valve, pressure valve, solenoid valve, proportional valve. Most of the lines and the connector within the corrosion product. There is an air compressor system of liquid water will accelerate the failure of the lubricating oil; liquid water is often in the oil core formed on the surface of water film, not only to reduce the oil core area of operation, also increased the oil core resistance. Oil core job cuts,gas through the filter layer speed obvious progress, when the flow rate is greater than0.4 m / s, the long time running oil, compressor oil consumption increased experience,may increase the amount of compressed air oil. Aqueous film forming oil coreresistance increases, the machine efficiency decline, serious when can cause the motor thermal maintenance. But water and dust are not the same, negative effects of water on the screw machine can go through a certain way to decrease. On the oil tankinsulation is a very useful method for the.

When the environment temperature of 30 degrees, the exhaust temperature of 80 degrees, the oil tank wall temperature is below 60 degrees, about 0.8MPa exhaust pressure machine, 60 degrees Celsius is now below the pressure dew point, moisturewill be like a winter indoor or in car glass window dew on the attached to the oil tankwall surface, water into the lubricating oil, with the oil flow to various parts of the machine. On the oil tank insulation is progress of oil tank wall exterior temperature,which is always less than the oil tank pressure dew point temperature, thus greatlyimproving the negative effects of water on the screw machine. The most simple way is in the insulation oil tank wall brushing a layer of thermal pipe insulation paint (1 mmthickness can improve the wall temperature of about 10 degrees). Oil tank, heat insulation and energy saving effect after disposal.

Reminder.

Chronicles and the electromechanical device limited company to recommend air compressor, water heater, air compressor heat recovery equipment, as long as youhave the air compressor factory, can 0 operation cost of producing hot water andheating.

See details > >

(this paper mainly introduced to give oil tank insulation, but in actual in the problem solving process is for reference only.)

 
专业提供:空压机热水器空压机余热回收空压机余热利用空气能热水器系列
Address:Qinghu cun, Qishi Town, Dongguan, Guangdong Province Tel:+86-0769-86723636 Fax:+86-0769-82820762
All rights reserved © DongGuan ZhiHe Mechanical and electrical equipment Co., LTD   
网站地图    sitemaps